At ten past four in the morning, something inside the wall goes off like a dropped toolbox. Nobody is up. Nothing seems wrong. Then it happens again a few minutes later. Often that is the irrigation system finishing one zone and moving to the next, and the sound is water hammer. Water hammer pipes make the same bang when the washing machine stops filling, when the dishwasher shuts off, or when someone flips a single-handle faucet closed in a hurry.
It sounds dramatic, and it isn’t something to shrug off. The bang is the plumbing absorbing a pressure spike, and every one of those spikes stresses joints, valves and supply hoses somewhere in the house.
What Actually Causes the Bang
Water moving through a pipe carries a surprising amount of momentum. When a valve closes gradually, that water slows down gently. When a valve snaps shut in a fraction of a second, the moving column of water slams into it and stops all at once. The energy has to go somewhere, so it bounces back through the pipe as a pressure wave. If the pipe has any room to move, it jumps and strikes the framing, and that is the knock you hear.
The appliances most likely to cause it all use electric valves that close instantly:
- washing machines
- dishwashers
- refrigerator ice makers and water dispensers
- irrigation valves
- some toilet fill valves
Lever-style faucets can do it too, when they are pushed closed quickly. Older two-handle faucets that close with several turns rarely cause it.
The Sound Tells You What Kind of Noise It Is
Not every noise in the pipes is water hammer, and the fix depends on which one you have.
One sharp bang right after water shuts off. This is classic water hammer. Pipes knocking when water is turned off almost always means a fast valve plus something that makes the shock worse, usually high pressure or loose pipes.
Rattling or vibrating while water is running. This points to pipes that aren’t held firmly, or to water moving very fast through a narrow pipe. It isn’t hammer, though the causes overlap.
Ticking or creaking as hot water runs. That is usually pipes expanding as they warm up and rubbing against wood or straps. It is mostly harmless.
Humming or a high whine. Often a sign of high pressure or a partly closed valve forcing water through a small opening.
Rumbling or popping from the water heater. That is sediment in the tank, not your pipes, and it is a separate issue.
High Water Pressure Makes Everything Worse
The faster water moves and the more pressure is behind it, the harder the hit when a valve closes. That is why water hammer often starts, or gets louder, when house water pressure is too high.
Pressure varies a lot across the Valley. The Las Vegas Valley Water District says operating pressure in its system ranges from about 30 to 100 psi depending on elevation and demand, and that sustained pressure above 80 psi can damage household plumbing. The District also notes that most plumbing professionals recommend setting a pressure reducing valve between 35 and 60 psi, and that where static pressure exceeds 80 psi, installing and maintaining that valve is the property owner’s responsibility. A Department of Energy building guide adds that most plumbing codes require a pressure reducing valve where supply pressure exceeds 80 psi, and links high pressure to leaking pipes, dripping faucets and louder dishwashers and washing machines.
You can check your own pressure with an inexpensive gauge that threads onto a hose bib. Test it with no water running anywhere in the house, ideally once in the morning and once at night, since pressure can change through the day. If it reads above 80 psi, the pressure is part of your problem. For where the regulator sits and how it works, see our post on low water pressure at home.
When the Banging Means the PRV Is Failing
A pressure reducing valve, or PRV, is a spring-loaded valve on the main line, usually near where water enters the house. Look for a bell-shaped brass fitting on the incoming pipe, typically on the street-facing side of the house. Over time, its internal parts wear or get coated in scale, and it lets more and more street pressure through.
These signs often show up together when a PRV is failing:
- water hammer that starts suddenly, or gets louder, without any change in your fixtures
- a pressure gauge reading that creeps up over weeks
- faucets and showers that blast or spit when first opened
- toilets that fill loudly or keep running
- a water heater relief valve that drips
The last one deserves attention on its own. A dripping relief valve can mean the pressure inside the water heater is too high, and a relief valve is a safety device, so don’t plug or cap it. The District recommends that a licensed plumber adjust or service a PRV, and that is the right call. Setting it requires the correct pressure gauge and some care, and a valve that has worn out internally needs replacing rather than adjusting.
The Fixes That Actually Stop It
Bring the pressure down. If the pressure is high, adjusting or replacing the PRV often solves the problem everywhere at once, and it lowers wear on every appliance and fixture in the house.
Add water hammer arrestors. An arrestor is a small sealed cylinder with an air cushion or spring behind a piston. When the pressure spike hits, the piston compresses and absorbs it. The most common places for them are the washing machine hookups, where screw-on versions fit between the valve and the hose, and under the dishwasher or ice maker supply. Arrestors installed inside walls for whole-house protection are a plumber’s job.
Secure loose pipes. If you can reach the pipes, in a garage, an unfinished wall or an attic, check that they are strapped down along their run. A pipe that can move will hit things. Padded straps or clamps stop the movement. Supply lines running through the attic, which many Valley homes have, are worth a look too, since nobody sees them day to day.
Recharge old air chambers. Some older homes have short capped pipes behind fixtures that hold a pocket of air to cushion the shock. Over time, the air dissolves into the water and the chambers fill up. Draining the system can refill them with air: shut the main valve, open the highest and lowest faucets in the house until they stop running, then close them and turn the main back on slowly. If the banging returns quickly, arrestors are the more lasting answer.
Give the irrigation valves their own cushion. For irrigation, a plumber may be able to add an arrestor near the valve manifold, which spares the house pipes from the nightly hammering.
Why It Is Worth Fixing
Each bang is a short burst of pressure much higher than normal, and it targets the weakest points: soldered joints, threaded fittings, valve seats and the braided supply hoses on washers, faucets and toilets. Those are exactly the parts that start leaking when they wear out. Our article on preventing pipe leaks has more ways to take strain off the system, and a yearly plumbing preventative maintenance visit is a sensible moment to get your pressure checked.
Quieting the Pipes
Check the pressure, listen for which appliance sets it off, and secure what you can reach. If the gauge reads high, the PRV is acting up or the banging is coming from inside a wall, Dr. Cool can test, adjust or replace the valve and install arrestors where they’re needed. Book plumbing repair online or call (702) 873-1800, and request a visit today if the banging is new.
Frequently Asked Questions
Can a water heater expansion tank stop water hammer?
No. An expansion tank absorbs the slow pressure rise as water heats up in a closed system, while an arrestor absorbs the sudden spike from a valve snapping shut. They solve different problems, and some homes need both.
Does water hammer happen in PEX and other plastic pipe?
Yes. The pressure spike is the same, but flexible plastic pipe tends to absorb more of the movement, so the bang is often softer. Watch exposed plastic lines for a visible jump when an appliance shuts off, because unsecured runs can still rub and strain their fittings.
Why did water hammer start after I got a new washing machine?
Many newer washers fill in short, sharp bursts using electric valves that close very quickly. An older machine on the same hookup may never have caused a problem. Screw-on arrestors on both the hot and cold washer valves usually solve it, since treating only one side can leave the other banging.
Do water hammer arrestors wear out?
They can. Arrestors with a sealed air chamber can lose their cushion slowly over many years. If the banging returns at a fixture that already has one, the arrestor may need replacing, or the pressure may have climbed since it was installed.
Is it safe to adjust my own pressure reducing valve?
The Las Vegas Valley Water District recommends having a licensed plumber do it. An adjustment without a gauge can push pressure even higher, and a worn valve often won’t hold any setting, so a plumber will first confirm whether the valve can still be adjusted or has to be replaced.
Why do my pipes knock only at night?
Nighttime banging is usually the irrigation system cycling between zones, or a dishwasher or washer on a delay timer. Pressure is also often higher at night when neighborhood demand drops, which can make an existing hammer problem louder.