It tends to happen late at night, when the house is still. Someone finishes a shower, the water heater fires up to replace what they used, and from the garage comes a sound like popcorn in a covered pot. A water heater making popping noise like that is not about to burst, but it is telling you something about the bottom of the tank.
That something is almost always sediment. With Las Vegas Valley water, it builds up quickly, and the sound gets louder as it does. Here is what is going on inside, what you can do about it yourself, and how to tell when the problem has gone past the point a flush can fix.
Steam Bubbles Bursting Under a Crust of Scale
Every time water is heated, some of the dissolved minerals in it, mostly calcium and magnesium, come out of solution. They drift down and settle on the floor of the tank as a gritty layer. Over months and years, that layer packs down and hardens into scale.
Water gets trapped in and under that crust, right where the heat is strongest. On a gas heater, that is directly above the burner. The trapped pockets overheat, flash into small bubbles of steam and force their way up through the deposit. Each bubble that breaks free makes a pop. When there are enough of them at once, the pops run together into a steady rumble.
Because it only happens while the heater is actively heating, the noise comes and goes. You’ll notice it most after heavy use, when a full load of cold water has just come in and the burner or elements are running hard.
Las Vegas Water Builds That Crust Fast
Our water carries a heavy mineral load. The Las Vegas Valley Water District’s own figures put it at roughly 290 parts per million, about 17 grains per gallon, which falls squarely in the “very hard” category. That’s a lot of dissolved mineral passing through your water heater every day, and a good share of it stays behind.
Practically, that means a tank here can start popping within a few years of installation, sometimes sooner in a busy household. The same scale shows up as white crust on your showerheads and spots on your glassware. For the chemistry, see our piece on what causes hard water.
Rumbling, Popping and Crackling Come From Different Places
The type of noise tells you a little about where the sediment is sitting.
Popping and rumbling are typical of gas water heaters. The burner heats the tank from below, so the thickest sediment sits right over the flame. Water heater rumbling usually means the layer has grown thick enough for many bubbles to form at once.
Crackling or sizzling is more common on electric models. Electric heaters have one or two heating elements that poke into the water from the side of the tank. Scale collects on and around the lower element, and water sizzles against it as it heats. Water heater crackling that gets louder over time often means the element is gradually being buried.
A single bang after you shut a faucet is a different problem altogether. That’s usually water hammer in the pipes, not sediment in the tank, and it is worth mentioning separately if a technician comes out.
The Sound Is Harmless, the Scale Behind It Is Not
The popping itself won’t hurt anything. What causes it slowly will.
Scale acts like insulation between the heat source and the water. The burner or element has to run longer to deliver the same hot water, and the steel at the bottom of a gas tank gets hotter than it should. Over time that extra heat stresses the tank’s inner glass lining, and it’s a common reason tanks start leaking from the bottom years before you’d expect.
On electric heaters, a lower element buried in scale can overheat and burn out. If the hot water runs out much faster than it used to, sediment is a likely suspect.
Sediment also takes up space. A tank with several inches of scale on the floor holds less hot water than the label says.
A Flush Clears Loose Sediment
Draining and flushing the tank removes the loose grit before it hardens. On a heater that is only a few years old and has started making noise recently, a good flush often brings the quiet back.
The basic idea is simple. With the heat source off and the cold supply shut, you connect a hose to the drain valve at the base of the tank, run it somewhere that can handle hot, cloudy water, and let the tank empty. Briefly opening the cold supply while the drain is open stirs up the bottom and pushes out more sediment. Once the water runs clear, you close the drain, refill the tank completely and open a hot tap in the house until the air stops sputtering out. Only then does the power or gas go back on.
That last step matters most on electric heaters. Switching the power on before the tank is full can burn out a dry element in seconds.
Gas shutoff and relighting steps vary by model, so follow the instructions on the label or in the manual. If you’re not sure how your gas control works, leave the flush to a plumber. Our guide to hot water heater maintenance covers the rest of a yearly routine.
When a Flush Comes Too Late
A flush is a maintenance step, not a cure for years of buildup. A few situations change the answer.
The drain barely trickles. Hardened chunks of scale can block the drain valve, especially the plastic valves found on many standard tanks. If you open it and get a weak dribble of milky water, more flushing won’t reach the hard layer underneath.
The tank has never been flushed and is getting older. Scale that has sat for many years can be holding small weak spots in the tank bottom closed. Disturbing it can occasionally expose a leak that was already there. On an older heater with a long history of popping, it is worth having a plumber look at the tank before anyone opens the drain.
The drain valve won’t close properly afterward. Grit can lodge in the valve seat and leave a slow drip. A plumber can replace the valve.
In those cases, the age of the heater and the condition of the tank, anode rod and burner or elements decide whether a flush, a repair or a replacement makes sense. Plenty of noisy heaters have years left in them. Some don’t, and an honest assessment saves you from spending money on one that is close to the end.
Signs It Is More Than Sediment
Popping by itself can wait for a convenient appointment. These can’t:
- You smell gas. Get out of the house without flipping any switches, then phone Southwest Gas or 911 once you’re outdoors.
- Water or steam is coming from the relief valve on the side or top of the tank. That valve opens when temperature or pressure gets too high.
- The hot water is scalding when it used to be comfortable. A failing thermostat or gas control can let the tank overheat.
- There’s water pooling under the tank or rust-colored streaks down its side.
- You see scorch marks or soot around the burner opening of a gas heater.
For any of these, turn the heater off (gas control to off, or the breaker for an electric unit) and call for water heater repair rather than waiting.
Keeping the Popping From Coming Back
Once the tank is clean, a few habits keep it that way.
Flush on a schedule that fits your water. The Department of Energy’s Energy Saver guide suggests draining a quart from the tank every three months to clear sediment. With water as hard as ours, a full flush at least once a year on top of that makes sense, more often for large families or homes that use a lot of hot water.
Treat the hardness at the source. A water softener removes the calcium and magnesium before they reach the heater, which slows scale formation dramatically. A basic carbon filter improves taste but doesn’t do the same job. Dr. Cool can fit a softener or filtration system and explain which one suits your home.
Have the anode rod checked. The anode rod hangs inside the tank and gives itself up to corrosion, sparing the steel walls. In hard water it can become coated or wear away sooner than expected. Our explainer on what an anode rod does has more on this small but hardworking part.
Quiet Hot Water Again
Popping means sediment, and sediment caught early is easy to deal with. If a flush doesn’t settle things down or the tank is old enough that you’d rather not risk it, Dr. Cool can take a look. Schedule a visit online or call (702) 873-1800, and same-day service is available.
Frequently Asked Questions
Can a water heater explode from sediment?
Sediment on its own won’t make a tank explode. The temperature and pressure relief valve is there to release heat and pressure before they reach a dangerous level, which is why it should never be capped or blocked. If that valve is missing, painted over or plugged, have it replaced right away.
Can I flush a water heater that has a plastic drain valve?
Yes, but go easy on it. Plastic drain valves can crack if forced and clog quickly with scale, so open them slowly and don’t overtighten them afterward. If yours is stiff or already dripping, a plumber can swap it for a sturdier brass valve before the flush.
Do tankless water heaters make popping sounds?
They can, but for a slightly different reason. Minerals coat the heat exchanger’s tiny water channels rather than a tank floor, and that can cause ticking, popping or temperature swings. Tankless units are cleaned by circulating a descaling solution through them rather than by draining.
Is it normal for a new water heater to make noise?
A brand-new tank shouldn’t pop, because there’s no sediment yet. Light ticking as metal warms and cools is normal. If a heater only a few months old is already rumbling, the incoming water may be carrying grit from a recent main break or plumbing work, and a quick flush is a good first step.
Is it safe to keep using hot water while the heater is popping?
Generally, yes. Popping on its own doesn’t make the water unsafe to use or the heater dangerous to run. Plan a flush or an inspection in the next few weeks, and switch the heater off sooner if any of the warning signs above show up.