Fill a clear bottle about a third of the way from the kitchen tap, add a few drops of plain liquid soap, cap it and shake it hard for ten seconds. Soft water gives you a tall head of fluffy suds and clear water underneath. Hard water gives you a thin layer of bubbles and cloudy, milky water. If your bottle looks like the second one, a water softener not working is the likely reason your glasses keep spotting, and now you have proof.
In the Las Vegas Valley that result is hard to miss. The local water district measures hardness here at 17 grains per gallon (291 ppm) and labels that very hard, so when a softener stops doing its job, spotty glasses, crusty showerheads and stiff towels come back within days. Test strips give you an actual number if you’d like one, and our guide to testing for water hardness covers both methods. Once you’ve confirmed the water is hard, work through the causes below in order. The first few take minutes.
The Bypass Valve Is Turned the Wrong Way
Every softener has a bypass valve where the plumbing connects to the control head, either a push-button style or a lever or knob. In bypass, water flows around the softener untouched. It gets bumped during garage cleanouts, set to bypass during a plumbing repair and never switched back, or turned by someone filling a pool.
Check it first. If it’s in bypass, switch it to service and give the system a day to catch up. Run a manual regeneration if your control allows it.
The Salt Level Never Drops
When a water softener is not using salt, the most common reason is a salt bridge. A hard crust forms across the brine tank, usually a few inches above the water. The tank looks full of salt from the top, but there’s an empty gap underneath, so the water below never touches the salt and can’t make brine. Without brine, the resin can’t recharge, and the water stays hard.
To check for a salt bridge in a water softener, take a broom handle and push it gently down through the salt. If it stops at a hard layer partway down, that’s your bridge. Tap around the crust to break it into chunks rather than jabbing hard, since a brine tank can crack. Scoop out large pieces if they won’t break down, and let the softener regenerate afterward.
Bridges form when salt gets damp and fuses, which is more likely when the tank is kept topped up to the brim, when lower-purity salt is used, or when the tank sits somewhere humid. Keeping the tank no more than about half to two-thirds full of salt makes them less likely.
If there’s no bridge and the salt still isn’t going down, the softener may not be regenerating at all. Look at the sections on settings and the injector below.
Salt Mush at the Bottom of the Tank
Mushing is the bridge’s messier cousin. Instead of a crust at the top, dissolved salt recrystallizes into a thick sludge at the bottom of the brine tank. The sludge blocks the brine well and the intake, so the softener can’t draw brine even though there’s plenty of salt.
The fix is a cleanout. Let the salt run low, scoop out the remaining salt and sludge, flush the tank with clean water and refill it with fresh salt. Using a higher-purity salt and avoiding very fine salt makes mushing less likely to return.
The Settings Don’t Match Your Water
A softener only knows what you tell it. Two settings matter most.
Hardness. The control needs the hardness of your water in grains per gallon so it can work out when to regenerate. If someone entered a low number, or the unit came from a home with softer water, it will run out of capacity between regenerations. The district’s 17 grains per gallon is a sensible starting point unless your own test strip gives a different number.
Time and schedule. Most softeners regenerate in the middle of the night. If the clock was reset by a power outage, regeneration may now run in the middle of the afternoon, or on an older timer-based unit, it may not happen when it should at all. Check the time of day on the display and the regeneration schedule. If your household has grown, a timer-based unit may also need more frequent regeneration.
The Injector or Brine Line Is Clogged
The injector, sometimes called the venturi, is a small part inside the control head that creates suction to pull brine out of the tank. Sediment or salt debris can clog it, and the brine line that runs between the two tanks can kink or block.
Signs of a clog include a brine tank that fills with more and more water, salt that never goes down even though the control runs its regeneration cycle, and soft water that turns hard soon after regenerating. Many manuals describe how to remove and rinse the injector screen. If you’re not comfortable taking the control head apart, this is a good point to call a plumber.
The Resin Is Worn Out or Escaping
The resin beads inside the tall tank do the actual softening. They last for many years, but not forever, and chlorine in treated city water can wear them down over time. A softener with an old resin bed often regenerates normally, uses salt as expected and still delivers water that’s only partly soft.
Then there’s the more obvious sign: small orange or brown beads in your sinks, toilets or faucet aerators. The LVVWD water quality FAQ attributes these to filter media breakthrough from the softener. It suggests checking the outdoor hose bib first: if that water is clear, the problem is inside the house, and the district recommends contacting a professional plumber or the manufacturer. Beads escaping means a part inside the tank that should hold them back has failed.
Both resin replacement and internal repairs mean opening the tank, which is a job for a plumber.
Fix the Softener or Replace It
A broken bypass, a bridge, mush, a reset clock and a clogged injector are all simple fixes. Once you get into failing control valves, worn-out resin and cracked tanks on an older unit, replacement becomes a fair question, especially if the system is undersized for very hard water. Our water softener FAQ covers how these systems work in more depth, and our post on what causes hard water explains why the Valley’s water is so mineral-heavy in the first place.
Getting Soft Water Back
If the quick checks haven’t brought your soft water back, Dr. Cool’s water softening and filtration service can diagnose the softener, repair it or talk through replacement options with upfront pricing. Book online or call (702) 873-1800.
Frequently Asked Questions
How often should a water softener regenerate in Las Vegas?
It depends on the size of the system, your household’s water use and the hardness setting. With very hard water, many homes see regeneration every few days. A modern demand-initiated unit calculates this automatically from the water it measures, which is why the hardness setting matters so much.
Is it normal for water to sit in the brine tank?
Many softeners keep a few inches of standing water in the brine tank all the time, while others only add water shortly before regenerating. Check your manual. Water that keeps rising well above the normal level usually points to a clogged injector, a stuck valve or a drain line problem.
Can I use any salt in my water softener?
Most softeners accept common pellet or crystal softener salt, and many can also use potassium chloride. Avoid rock salt with a lot of insoluble material, which leaves residue in the tank, and follow the manufacturer’s guidance for your model.
Why does my soft water feel slippery?
That slick feeling is normal. Soap rinses off more easily in soft water, so your skin feels smooth rather than squeaky. It isn’t leftover soap or a sign that the softener is overdoing it.
Does a water softener need a drain?
Yes. Every regeneration flushes the minerals and spent brine down a drain line, usually to a laundry standpipe or floor drain. A kinked or blocked drain line can stop the softener from regenerating properly.